RCD-510 + 9W7 help

So, last week I ordered a Micro Can cable and I just ran an auto scan and received these following faults

Address 77: Telephone (J412) Labels: 7P6-035-730.clb
Part No SW: 7P6 035 730 C HW: 7P6 035 730 C
Component: TELEFON H05 0440
Revision: 1B001001 Serial number: 00007668281194
Coding: 0A00000000010100
Shop #: WSC 00000 000 00000
ASAM Dataset: UHVNA A01007
ROD: UHVNA.rod
VCID: 3245F9EB65E2E9D12F-8066

3 Faults Found:
9457427 - Left audio channel for speech/telephone
B104F 13 [008] - Short to GND
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 4
Fault Frequency: 1
Reset counter: 30
Mileage: 203040 km
Date: 2019.09.09
Time: 20:07:42

9457171 - Right audio channel for speech/telephone
B104E 13 [008] - Short to GND
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 4
Fault Frequency: 1
Reset counter: 30
Mileage: 203040 km
Date: 2019.09.09
Time: 20:07:40

13636352 - Control module not coded
U1013 00 [009] - -
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 4
Fault Frequency: 1
Reset counter: 124
Mileage: 193635 km
Date: 2019.07.11
Time: 20:21:38

Address 56: Radio (J503) Labels: 5M0-035-1xx-56.clb
Part No SW: 1K0 035 180 AC HW: 1K0 035 180 AC
Component: Radio Prem-8 H10 0035
Revision: -----20S Serial number: VWZ4Z7K1139295
Coding: 0100040004
Shop #: WSC 01357 011 00200
VCID: 61E746A77884224986-8034

1 Fault Found:
00821 - Antenna 2 for Radio (R93)
011 - Open Circuit
Freeze Frame:
Fault Status: 01101011
Fault Priority: 5
Fault Frequency: 52
Reset counter: 253
Mileage: 132171 km
Time Indication: 0
Date: 2016.10.26
Time: 07:18:35

Address 19: CAN Gateway Labels: 7N0-907-530-V1.clb
Part No SW: 7N0 907 530 HW: 1K0 907 951
Component: J533 Gateway H27 5603
Revision: H27 Serial number: 030810F1000908
Coding: E9807F0600161200000002
Shop #: WSC 02645 444 105056
VCID: 6DFF2A97745C762932-8038

1 Fault Found:
01303 - Telephone Transceiver (R36)
004 - No Signal/Communication - Intermittent
Freeze Frame:
Fault Status: 00110100
Fault Priority: 2
Fault Frequency: 1
Reset counter: 29
Mileage: 144096 km
Time Indication: 0
Date: 2017.07.10
Time: 11:40:23

If any of this helps or know how to resolve these it would be appreciated. All I did was run the scan. I did not clear and run again yet.

Carlosfandango said:

This is the label on mine, it shows a far different SW and HW number!

Sent from my iPhone using Tapatalk

Click to expand...

I just looked at my module that was in my car and it is the same part number as yours, but mine is G

Nick_MKVI said:

I just looked at my module that was in my car and it is the same part number as yours, but mine is G

Click to expand...

It looks like both of your units are different revisions of the same module

See here,
https://www.ecstuning.com/b-genuine-volkswagen-audi-parts/interfbox/5k0035730g/

Are you actually putting any of these part numbers and other info into google?? I'm finding plenty of info.


Sent from my iPhone using Tapatalk

Carlosfandango said:

It looks like both of your units are different revisions of the same module

See here,
https://www.ecstuning.com/b-genuine-volkswagen-audi-parts/interfbox/5k0035730g/

Are you actually putting any of these part numbers and other info into google?? I'm finding plenty of info.


Sent from my iPhone using Tapatalk

Click to expand...

I am. Trying to read through a lot, so I may be missing something within all of the pages I am finding. I am wondering if there's an issue with the coding. Now that i have VCDS access I can troubleshoot. I did read something if the workshop number is incorrect or all 0's it can cause issue and to change it to 1234/123/1234 and it should then recognize the module.

Nick_MKVI said:

I am. Trying to read through a lot, so I may be missing something within all of the pages I am finding. I am wondering if there's an issue with the coding. Now that i have VCDS access I can troubleshoot. I did read something if the workshop number is incorrect or all 0's it can cause issue and to change it to 1234/123/1234 and it should then recognize the module.

Click to expand...

After seeing your earlier fault scan it does look like it could be a code issue!


Sent from my iPhone using Tapatalk