GOLFMK8
GOLFMK7
GOLFMK6
GOLFMKV

Group Buy Meth Injection Kit

Turn8

Ready to race!
pm'd

anyone else know about the bolt issue, and what the correct length/thread is?

Yep, my PagParts bolts didn't fit.

I purchased two sizes:
M6-1.0x60mm
&
M6-1.0x75mm

The 60mm are good but, I think the 75mm's will work and have more thread in the manifold.

I still haven't installed my kit. I just don't have the time. Anyone want to do it for me? ;)

Mike
 

mustache rash

Go Kart Champion
So I'm thinking of upgrading to a devilsown nozzle.

What size would anyone recommend?
D03 or D02?

I'm running a single nozzle in the lower bung of the bsh tbp.

I use it only for cooling.....
 

U-20T

Go Kart Champion
So I'm thinking of upgrading to a devilsown nozzle.

What size would anyone recommend?
D03 or D02?

I'm running a single nozzle in the lower bung of the bsh tbp.

I use it only for cooling.....

Go AM they are by far the best on the market. Get a .6mm, jet holder, 1ft 4mm line and a 6mm to 4mm pushlock fitting.
 

ViRtUaLheretic

╭∩╮(︶__︶&#6
So I'm thinking of upgrading to a devilsown nozzle.

What size would anyone recommend?
D03 or D02?

I'm running a single nozzle in the lower bung of the bsh tbp.

I use it only for cooling.....
Id recommend DO3

Yep, my PagParts bolts didn't fit.

I purchased two sizes:
M6-1.0x60mm
&
M6-1.0x75mm

The 60mm are good but, I think the 75mm's will work and have more thread in the manifold.

I still haven't installed my kit. I just don't have the time. Anyone want to do it for me? ;)

Mike
The bolts provided with the PPT TB spacer are absolute shit

ugh..i know...wating on an aluminum mani for that. the thought of drilling that plastic makes me dizzy
Grab a blanket and get cozy, you are going to be waiting a while ;)

i was thinking about that b/c my TB pipe is so wrapped with insulation, a tb spacer may push it into the fans. i have maybe 1/2" clearance as it is. id hate to lose the insulation.

we need to spitball this.
You wrapped the TB with heat wrap? got any pix?
And here I thought I went overboard ;p
 

allset

Go Kart Champion
Id recommend DO3


The bolts provided with the PPT TB spacer are absolute shit


Grab a blanket and get cozy, you are going to be waiting a while ;)


You wrapped the TB with heat wrap? got any pix?
And here I thought I went overboard ;p

so they are def M6?

no pics, wrapped in DEI titainium wrap and DEI reflective foil tape on top of that. want to maximize the cooling w/m spray from the IC port so i wrapped the hell out of it.
 

Thumper

Autocross Champion
so they are def M6?

no pics, wrapped in DEI titainium wrap and DEI reflective foil tape on top of that. want to maximize the cooling w/m spray from the IC port so i wrapped the hell out of it.

What we need is a vented hood with a duct piping the air straight up from the radiator and out the hood. :D :D :D :D
 

skateboy___918

Ready to race!
has anyone found a pressure gauge with a max needle yet? I like one for my setup so everyone in awhile I can check to make sure my pump is still making consistent pressure

 

allset

Go Kart Champion
has anyone found a pressure gauge with a max needle yet? I like one for my setup so everyone in awhile I can check to make sure my pump is still making consistent pressure


i got a nice small one from mcmaster.com i ran in line in the engine bay

search gauges in the site
 

allset

Go Kart Champion
Is that mean I need pipe to match the K04 when I can finaly install it? It looks pretty much the same as my previous..

The ko3 version is longer and has a slight anlge toward the turbo for the sleeve and coupler.

the new one is designed for aftermarket ko4 kits which have a 90 deg silicone elbow. it is shorter and is not angled toward the turbo.

The ko3 will fit but not perfectly. The new design is a much better fit
 

allset

Go Kart Champion
paul- why are you getting rid of your BSH pipe?

i decided to put the nozzle way back by the IC outlet to allow more time for evaporation. Plus Neuspeed:D
 

allset

Go Kart Champion
Top