Barische's Car Build

APR stage 1 tune
APR carbonio intake
Audi R8 coil packs/ NGK spark plugs
Euro Short Shifter
shortened shift lever
Stern Subframe bar
ECS dogbone mount
20% rear, 40% front tint
trans fluid (gm syncromesh /redline MTL mix)
APR rear sway bar
Ultra racing mid brace
Unibrace xb
Tyrol brake caliper bushings - front
Ate blue brake fluid flush
Hardwired rx65
Front - Hawk HP+ pads (ate away rotors but great stopping power)
New set: EBC yellow stuff
rear - stoptech street performance pads
034 mounts engine/BFI trans insert w windo weld fill - track durometer
Forge side to side quick shifter
windoweld filled shifter bushings
Verdict motorsport shifter bracket bushings
windo weld Filled Lower control arm bushings
17" enkei Fujins w/ bridgestone re-11, re070 (previous = Dunlop direzza z1 star specs)
alacrity delrin black shift knob, alcantara boot
godspeed/ebay catback
H&R sport springs / Bilstein B8 mkv shocks

next mods: trailing arm, front control arm front inner bushing


H&r RSS

too stiff taken off for bilstein / h&R sport combo

400# front - 450# rear springs

IMG_4422 by barische, on Flickr

IMG_4843 by barische, on Flickr
IMG_4425 by barische, on Flickr




BFI stage 1 insert


IMG_0838 by barische, on Flickr

Forge side shifter


GTI by barische, on Flickr

034 motor mount


GTI by barische, on Flickr

Stern brace


IMG_0306 by barische, on Flickr

Home race setup


GTI by barische, on Flickr

auto-x helmet


GTI by barische, on Flickr

wrapped the exhaust pipe with titanium exhaust wrap and stainless steel ziptie to stop the rubbing rattle..

IMG_0302 by barische, on Flickr

OEM gear oil


GTI by barische, on Flickr

old sorry OEM bushings


IMG_0333[1] by barische, on Flickr

tyrol bushings -


IMG_0336[1] by barische, on Flickr



Bushing DIY - http://golfmk6.com/forums/showthread.php?t=32668

after re-11/re070 went on
IMG_4850 by barische, on Flickr
Ultra racing mid brace



30k miles


GTI by barische, on Flickr

Honestly that doesn't look like 20s in the back and 40s in the front (tint). =D Nonetheless it's clean. I'd say get some smoked side markers or color matched markers, and she'll look even better.

Once you start modding, there is never really a true "done" you're gonna wanna do more and more and more and more. =D Enjoy your car.

Ukrkid37 said:

Honestly that doesn't look like 20s in the back and 40s in the front (tint). =D Nonetheless it's clean. I'd say get some smoked side markers or color matched markers, and she'll look even better.

Once you start modding, there is never really a true "done" you're gonna wanna do more and more and more and more. =D Enjoy your car.

Click to expand...

What do you think it is then? 35% in the back and 50% in the front

Just did seafoam, no error codes.. Went without a hiccup.. Small amount of smoke.

Just ordered APR rear swaybar. Will be installing it probly next weekend or week night this week.

Apr bar installed, still have to test it put but at middle settings it feels pretty flat, less understeer

Just ordered Tyrol Bushings $94

Will update you guys on how it goes with install.. Will try to take lots of pics.

Next for Brakes: Hawl HP+ pads and SS lines

Tyrol bushings r in

Looks good bud. :thumbup:

Bushings are in here are more pics along with DIY

http://golfmk6.com/forums/showthread.php?t=32668

swfloridamk6 said:

Looks good bud. :thumbup:

Click to expand...

thanks

New stuff, pads, bleeder, suspension bolts, fluid

Hawk hp+ front pads have sensor on both sides. Should i just remove the sensor piece out of the passenger side pad?

Cut the wire? Remove w/ needle nose? I checked the part# which are correct.

Does the rears pads have sensor as the new yellows did not come w/ sensor?

USP SS lines are at my parents house..

Just did soundaktor delete, and took the airbag stickers off

Just ordered ultra racing mid brace