NickFury
New member
I'm driving Golf Mk6 1.4 TSI 122 HP 2009 and after casual VCDS scan it showed me some concerning fault code
Address 02: Auto Trans Labels: 0AM-927-769.clb
Part No SW: 0AM 300 048 L HW: 0AM 927 769 D
Component: GSG DSG AG7 431 2669
Revision: 00043014 Serial number: CU501310127451
Coding: 0000020
Shop #: WSC 00069 730 10090
VCID: 397998E370599B4E0C-806C
1 Fault Found:
006012 - Clutch 2
P177C - 003 - Tolerance Limit Reached - Intermittent
Freeze Frame:
Fault Status: 00100011
Fault Priority: 0
Fault Frequency: 3
Reset counter: 10
Mileage: 115736 km
Time Indication: 0
Date: 2014.12.10
Time: 05:10:57
I did the scan day before and nothing was there. I'm not sure if I can recognize any problem while driving.
Before I break the bank and leave my car to the mechanic should I try to erase the code and see if it comes back or should I test the car in some specific driving conditions?
I've read about this issue and some suggested to update the software, is it just a transmission SW update or something else ? I did stage 1 to the ECU a week ago and no idea if it can be related.
Update: tried to remove the fault code but it came back after a short drive. It’s only viewable in VCDS no warning lights on dashboard though.
Now the fault code is:
1 Fault Found:
006012 - Clutch 2
P177C - 003 - Tolerance Limit Reached
Freeze Frame:
Fault Status: 01100011
Fault Priority: 0
Fault Frequency: 1
Reset counter: 10
Mileage: 115747 km
Time Indication: 0
Date: 2014.12.10
Time: 11:35:16
Address 02: Auto Trans Labels: 0AM-927-769.clb
Part No SW: 0AM 300 048 L HW: 0AM 927 769 D
Component: GSG DSG AG7 431 2669
Revision: 00043014 Serial number: CU501310127451
Coding: 0000020
Shop #: WSC 00069 730 10090
VCID: 397998E370599B4E0C-806C
1 Fault Found:
006012 - Clutch 2
P177C - 003 - Tolerance Limit Reached - Intermittent
Freeze Frame:
Fault Status: 00100011
Fault Priority: 0
Fault Frequency: 3
Reset counter: 10
Mileage: 115736 km
Time Indication: 0
Date: 2014.12.10
Time: 05:10:57
I did the scan day before and nothing was there. I'm not sure if I can recognize any problem while driving.
Before I break the bank and leave my car to the mechanic should I try to erase the code and see if it comes back or should I test the car in some specific driving conditions?
I've read about this issue and some suggested to update the software, is it just a transmission SW update or something else ? I did stage 1 to the ECU a week ago and no idea if it can be related.
Update: tried to remove the fault code but it came back after a short drive. It’s only viewable in VCDS no warning lights on dashboard though.
Now the fault code is:
1 Fault Found:
006012 - Clutch 2
P177C - 003 - Tolerance Limit Reached
Freeze Frame:
Fault Status: 01100011
Fault Priority: 0
Fault Frequency: 1
Reset counter: 10
Mileage: 115747 km
Time Indication: 0
Date: 2014.12.10
Time: 11:35:16
Last edited: