Search results

just had my 034 motormount metal housing break, motor shifted in motor bay, tore oil line to turbo... getting wreckered to shop to see if further damage , fucking so pissed right now!!!!! pics shortly

I noticed when going into a driveway or any surface that is higher or lower the rear sway bar will make a loud noise if I approach at an angle causing one of the rear tires to raise/lower independent of the other. Is this normal or do I need to check it out? The rear sway bar seems pretty...

Ive been calling tuning shops in the southeast about tuning my mk6 and ive been getting quotes between 500~600 dyno tune. when i specifically ask if they can tune tsi motors they say of course no problem. ive always been under the impression that you needed proprietary hardware and software to...

As title states, I am looking for a tuner in the panhandle area or anyone that can custom tune my Mk6 GTI. I am located between Pensacola and Panama City. Thanks ahead!

RP4-VW11 ... Allows plug and play for ~$100 specifically for VW http://www.amazon.com/Rp4-vw11-Radiopro4-Interface-Select-Vehicles/dp/B0072LCX4G AXXESS ASWC-1 ... "universal" steering wheel control adaptor for ~$65 http://www.sonicelectronix.com/item_68038_Axxess-ASWC-1.html I'm looking for...

I'm looking for a small amp to amplify stock speakers in an oem manner, by that i mean use stock speaker wire an not have to run new lines. Does anyone know of an amp that can be integrated into the stockaudio system for not alot of money...

specifically whiteline 24mm adjustable

I just installed my 034 motor mount The one on the right... Did anybody notice the arm with the two bolts that mount to the motor moves inside of the main mount body? When I went to bolt up the new mount I thought I was sent the wrong one because the holes were WAY off, I held the mount and...

I've noticed an issue sometimes trying to get out of reverse a month or two after installing FX350. I will be backing out of a spot and when I depress clutch to put it into 1st it will not budge out of reverse. I usually have to turn the car off to get it out of reverse, but one time I lightly...

i have insert right now but going to tear out entire lower mount for hpa subframe mount. my question is do i use the washer thats meant to hold in the insert on the hpa? it looks like on install directions they dont use washer , just bolt. also my bfi insert came with bolt thats currently...

43k miles

my alignment went out so had to get it fixed, i know caster and camber are equalized and only adjustable by shifting subframe, camber was pretty good only 1.x each side but caster was 9.x both sides , did installing vwr springs throw out caster that far?? i was going to install the walk kit but...

thinking of getting one to replace my catback when i feel like being a bit louder , but the only ones i can find are weld on ...

http://www.034motorsport.com/chassis-components-volkswagen-transmission-mount-density-line-mk5-vw-20t-fsi-32l-vr6-p-21996.html Says it uses solid rubber instead of poly ... thinking of pairing up that 034 tranny mount with the SPM motor mount for $150 (...

https://www.dropbox.com/s/vczo49fiv07a18u/LOG-05-03F-20F-311-1148-115Crun5.csv https://www.dropbox.com/s/7402wwwlp51eyz4/LOG-03-011-032-311-54C-1014-1145-115Crun3.csv https://www.dropbox.com/s/oaw5bsbvstitxwq/LOG-01-011-038-20F-311-544-1014-1144-1158-run2.csv...

New clutch assy Make sure you have engine bar! Old clutch Semi-liquid tar grease, brake/clutch fluid mixed with clutch particles created this New flywheel New clutch CLEAN housing! Overall it was a pain in the butt, I don't want to go through it again. However, if you are getting...

GT28RS Stock Location Turbo & Manifold for 2.0T FSI / TSI Models http://www.atpturbo.com/mm5/merchant.mvc?Screen=PROD&Store_Code=TP&Product_Code=ATP-VVW-255 http://www.youtube.com/watch?v=49Ju0EI-Jc8 This kit came out a couple years ago and at first it didn't really catch on as there was...

going to be upgrading clutch soon, I'll probably go ahead and replace the rear main seal, however not sureif i should replace the axle seals as well? i haven't heard or read about them failing much... http://www.hstuning.com/product_info.php?products_id=3631...

going to install full clutch and wondering what else to do while inthere. can't do lsd (to expensive) but does anyone have any suggestions ?

I got a shipment of some stuff in so I decided to take a family picture That stripped AR on the far left is waiting on a freefloat handguard and then it will be reassembled. Other than that everything is 100% :)