The Golfmk6 Wheel/Fitment Info Thread!

[smittyjs]

I been looking to do around 2 to 2.2 inch drop on her. I was hoping to just get by with the fender screw mod and not rolling the fenders.

 

[SirClimax]

I been looking to do around 2 to 2.2 inch drop on her. I was hoping to just get by with the fender screw mod and not rolling the fenders.

I would drop it then look at the room you have for spacers

 

[smittyjs]

Ok thanks for the help man

 

[SirClimax]

Ok thanks for the help man

my pleasure!

 

[ahard48]

18x8.5 et45 front 18x9.5 et 40 rear. Stock height but going st in the future. Will I need anything other than 3degree camber and screw mod???

 

[ahard48]

Bump for info for above

 

[Michael58121]

is this a safe fitment and would i need spacers, ill be going air...also ill be getting the SRS-Tec front wide fenders the 2.5cm ones
Fronts: 18x9 et38 (215/35)
Rear: 18x9 et38 (215/35)

 

[SirClimax]

Just to share my experience I comfortably fit 18x8.5 et35 (225/40) on air and have no issues with rubbing! The tires are a little worn and I will report back when I put new ones on in the future if I run into any issues. My fenders are rolled and slightly pulled + fender screw mod.

 

[Invidious]

Looking for some insight from the wheel guru. Im looking to build my set of bbs rs035. I want to put 3.5" 16>18 slant lips with 16>18 inner barrels at 5.5" on these faces. I would like to tuck the lip within the rear quarters without any roll/pull. The back pad is 1" if that helps.. I have a total of 10 degrees of camber adjustment. My current setup is 18x10 et30 rear at -5.9 degrees of camber w/ 1mm clearance to strut. Will it work?


Sent from my iPhone using Tapatalk

 

[Wolfmk6]

I'm looking towards the mb battles that are 18x9.5 et15 wrapped with 225/40 r18
Would It require massive camber or fender rolling? To be tucking of course

 

[snobrdrdan]

I'm looking towards the mb battles that are 18x9.5 et15 wrapped with 225/40 r18
Would It require massive camber or fender rolling? To be tucking of course

LOL, I don't think those will fit with that offset
Lots of fender work/pulling

What suspension, out of curiousity?

 

[Wolfmk6]

LOL, I don't think those will fit with that offset
Lots of fender work/pulling

What suspension, out of curiousity?

I have bc coils

 

[mikeleemk6]

Calling all fitment gurus.... 18x8.5 and 18x9.5 et will be in the low to mid 30's 215 up front 225 rear? or 225 all around? im on air with rear idf upper control arms. Thanks.

 

[SirClimax]

Calling all fitment gurus.... 18x8.5 and 18x9.5 et will be in the low to mid 30's 215 up front 225 rear? or 225 all around? im on air with rear idf upper control arms. Thanks.

I'm not sure about the rear but I fit 18x8.5 ET35 on 225/40 after roll and slight pull with a tiny bit of room to spare when aired out

Sent from my SAMSUNG-SM-G920A using Tapatalk

 

[mikeleemk6]

I'm not sure about the rear but I fit 18x8.5 ET35 on 225/40 after roll and slight pull with a tiny bit of room to spare when aired out

Sent from my SAMSUNG-SM-G920A using Tapatalk

Thanks bud. I have ran 225/40/18 on all my previous sets of 18x8.5 but with the eta 45 and had no issues. Thank you for the insight tho. Seems like the 215 is expensive compared to the 225. Go figure lol.